MCU:STM32F429ZIT6
开发环境:STM32CubeMX+MDK5
外购了一个SPI接口的SD Card模块,想要实现SD卡存储数据的功能。
首先需要打开STM32CubeMX工具。输入开发板MCU对应型号,找到开发板对应封装的MCU型号,双击打开(图中第三)。
此时,双击完后会关闭此界面,然后打开一个新界面。
然后,我们开始基本配置。
现在我们选择一个LED作为系统LED,该步骤可以忽略,只是本人喜欢这样子。以硬件原理图的LD3为例子。
基本配置除了时钟树外,基本上已经配置好了。
现在配置时钟树基本配置已经配置完,现在开始配置实验使用的内容。
配置USART1,重定向printf函数作为串口输出。然后配置SPI1,作为驱动SD Card读写的接口。
然后配置文件系统,可以让文件的使用更方便。
现在配置按键,触发中断处理一些事情。
配置完成,完善工程,生成工程。
到此,STM32CubeMX工具的使用结束!可以发现在桌面已经生成了SDCard_rw工程。
使用MDK5打开SDCard_rw工程打开。点击魔法棒,勾选微库。选择对应的下载器,勾选下载完复位允许。USB线一端接开发板USB_Device,一端接PC。
现在可以开始实验了
在usart.c中重定向printf函数,并在usart.h中声明。
1 //重定向c库函数printf到串口DEBUG_USART,重定向后可使用printf函数
2 int fputc(int ch, FILE *f)
3 {
4 HAL_UART_Transmit(&huart1, (uint8_t *)&ch, 1, 1000);
5 return (ch);
6 }
在sdcard_write工程下创建UserCode文件夹,编写drive_spisd.c和drive_spisd.h。
然后在MDK5这里的SDCard_rw工程添加一个新文件夹UserCode,装入drive_spisd.c。并在魔法棒这里加入头文件路径。
drive_spisd.c如下
/* Includes ------------------------------------------------------------------*/
#include "drive_spisd.h"
/* Private includes ----------------------------------------------------------*/
#include "spi.h"
#include "ff.h"
#include "usart.h"
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
uint8_t test;
uint8_t SD_TYPE = 0x00;
MSD_CARDINFO SD0_CardInfo;
char SD_FileName[] = "hello.txt";
/* Private function prototypes -----------------------------------------------*/
static int SD_SendCMD(uint8_t cmd, uint32_t arg, uint8_t crc);
static uint8_t SD_ReceiveData(uint8_t *data, uint16_t len);
static uint8_t SD_SendBlock(uint8_t*buf, uint8_t cmd);
/* Private user code ---------------------------------------------------------*/
/**
* @brief SPI_CS片选
* @note None
* @retval None
*/
void SPISD_CS(uint8_t p)
{
HAL_GPIO_WritePin(SPI1_CS_GPIO_Port, SPI1_CS_Pin, (p==0)?GPIO_PIN_SET:GPIO_PIN_RESET);
}
/**
* @brief 发送命令(CMD0~CMD63),发完释放
* @note 命令格式:0+传输标志(1-命令、0-响应)+CONTENT(6+32)+7CRC+1
* @retval None
*/
static int SD_SendCMD(uint8_t cmd, uint32_t arg, uint8_t crc)
{
uint8_t r1,retry;
SPISD_CS(0); //取消片选
HAL_Delay(20);
SPISD_CS(1); //选通
//SD卡的SPI通信协议规定,每个命令操作之前都需要发送至少8个时钟周期
do
{
retry = SPI_ReadWrite(0xFF);
}while(retry != 0xFF);
SPI_ReadWrite(cmd | 0x40);
SPI_ReadWrite(arg >> 24);
SPI_ReadWrite(arg >> 16);
SPI_ReadWrite(arg >> 8);
SPI_ReadWrite(arg);
SPI_ReadWrite(crc);
if(cmd == CMD12)
SPI_ReadWrite(0xFF);
do
{
r1 = SPI_ReadWrite(0xFF);
}while(r1 & 0x80);
return r1;
}
//SD卡初始化
uint8_t SD_Init(void)
{
uint8_t r1,i;
uint8_t buff[6] = {0};
uint16_t retry;
SPI_SetSpeed(SPI_BAUDRATEPRESCALER_256);
SPISD_CS(0);
for(retry=0;retry<10;retry++)
SPI_ReadWrite(0xFF);
//SD卡进入IDLE状态
do
{
r1 = SD_SendCMD(CMD0 ,0, 0x95);
}while(r1 != 0x01);
//查看SD卡的类型
SD_TYPE = 0;
r1 = SD_SendCMD(CMD8, 0x1AA, 0x87);
if(r1 == 0x01)
{
for(i=0;i<4;i++)
buff[i] = SPI_ReadWrite(0xFF); //Get trailing return value of R7 resp
if( buff[2]==0X01 && buff[3]==0XAA ) //卡是否支持2.7~3.6V
{
retry = 0XFFFE;
do
{
SD_SendCMD(CMD55, 0, 0X01); //发送CMD55
r1 = SD_SendCMD(CMD41, 0x40000000, 0X01); //发送CMD41
}while(r1&&retry--);
if(retry && SD_SendCMD(CMD58, 0, 0X01) == 0) //鉴别SD2.0卡版本开始
{
for(i=0;i<4;i++)
buff[i] = SPI_ReadWrite(0XFF); //得到OCR值
SD_TYPE = (buff[0]&0x40) ? V2HC:V2;
}
}else
{
SD_SendCMD(CMD55, 0, 0X01); //发送CMD55
r1 = SD_SendCMD(CMD41, 0, 0X01); //发送CMD41
if(r1<=1)
{
SD_TYPE = V1;
retry = 0XFFFE;
do //等待退出IDLE模式
{
SD_SendCMD(CMD55, 0, 0X01); //发送CMD55
r1 = SD_SendCMD(CMD41, 0, 0X01); //发送CMD41
}while(r1&&retry--);
}else //MMC卡不支持CMD55+CMD41识别
{
SD_TYPE = MMC; //MMC V3
retry = 0XFFFE;
do //等待退出IDLE模式
{
r1 = SD_SendCMD(CMD1, 0, 0X01); //发送CMD1
}while(r1&&retry--);
}
if( retry==0 || SD_SendCMD(CMD16, 512, 0X01)!=0 )
SD_TYPE = ERR; //错误的卡
}
}
SPISD_CS(0);
SPI_SetSpeed(SPI_BAUDRATEPRESCALER_4);
return SD_TYPE?0:1;
}
void FileSystem_Init(void)
{
FATFS *fs;
DWORD fre_clust, AvailableSize, UserSize;
uint8_t res;
uint8_t *work;
uint16_t TotalSpace;
res = SD_Init();
if(res == 1)
printf("SD卡初始化失败! \r\n");
res = f_mount(&USERFatFS, USERPath, 1); //挂载
if(res == FR_NO_FILESYSTEM) //没有文件系统,格式化
{
printf("没有文件系统! \r\n");
work = malloc(_MIN_SS);
res = f_mkfs(USERPath, FM_FAT, 0, work, _MIN_SS); //格式化sd卡
free(work);
if(res == FR_OK)
{
res = f_mount(NULL, USERPath, 1); //格式化后先取消挂载
res = f_mount(&USERFatFS, USERPath, 1); //重新挂载
if(res == FR_OK)
{
printf("SD卡已经成功挂载,可以进进行文件写入测试! \r\n");
}
}
else
{
printf("格式化失败! \r\n");
}
}else if(res == FR_OK)
{
printf("挂载成功! \r\n");
}else
{
printf("挂载失败! (%d)\r\n", res);
}
res = f_getfree(USERPath, &fre_clust, &fs); /* 根目录 */
if ( res == FR_OK )
{
TotalSpace = (uint16_t)(((fs->n_fatent - 2) * fs->csize ) / 2 /1024);
AvailableSize = (uint16_t)((fre_clust * fs->csize) / 2 /1024);
UserSize = TotalSpace - AvailableSize;
/* Print free space in unit of MB (assuming 512 bytes/sector) */
printf("\r\n%d MB total drive space.\r\n%ld MB available.\r\n%ld MB used.\r\n",TotalSpace, AvailableSize, UserSize);
}
else
{
printf("Get SDCard Capacity Failed (%d)\r\n", res);
}
// f_mount(NULL, USERPath, 1); //取消挂载
}
/**
* @brief 读取指定长度数据
* @note None
* @retval None
*/
static uint8_t SD_ReceiveData(uint8_t *data, uint16_t len)
{
uint8_t r1;
SPISD_CS(1);
do
{
r1 = SPI_ReadWrite(0xFF);
HAL_Delay(100);
}while(r1 != 0xFE);
while(len--)
{
*data = SPI_ReadWrite(0xFF);
data++;
}
SPI_ReadWrite(0xFF);
SPI_ReadWrite(0xFF);
return 0;
}
/**
* @brief 向SD卡写入一个数据包(512字节)的内容
* @note None
* @retval None
*/
static uint8_t SD_SendBlock(uint8_t*buf, uint8_t cmd)
{
uint8_t r1;
uint16_t t;
do{
r1 = SPI_ReadWrite(0xFF);
}while(r1!=0xFF);
SPI_ReadWrite(cmd);
if(cmd != 0XFD) //不是结束指令
{
for(t=0; t<512; t++)
SPI_ReadWrite(buf[t]); //提高速度,减少函数传参时间
SPI_ReadWrite(0xFF); //忽略crc
SPI_ReadWrite(0xFF);
t = SPI_ReadWrite(0xFF); //接收响应
if( (t&0x1F) != 0x05 )
return 2; //响应错误
}
return 0; //写入成功
}
/**
* @brief CSD,卡的操作条件信息,128bit
* @note None
* @retval None
*/
uint8_t SD_GetCSD(uint8_t *csd_data)
{
uint8_t r1;
r1 = SD_SendCMD(CMD9, 0, 0x01); //读取CSD寄存器
if(r1 == 0x00)
r1 = SD_ReceiveData(csd_data, 16); //接收16个字节的数据
SPISD_CS(0); //取消片选
return r1?1:0;
}
/**
* @brief CID,卡识别号,128bit
* @note None
* @retval None
*/
uint8_t SD_GetCID(uint8_t *cid_data)
{
uint8_t r1;
r1 = SD_SendCMD(CMD10, 0, 0x01); //读取CID寄存器
if(r1==0x00)
r1 = SD_ReceiveData(cid_data, 16); //接收16个字节的数据
SPISD_CS(0); //取消片选
return r1?1:0;
}
//获取SD卡的总扇区数
uint32_t SD_GetSectorCount(void)
{
uint8_t n;
uint8_t csd[16];
uint16_t csize;
uint32_t Capacity;
if(SD_GetCSD(csd) != 0) //取CSD信息,如果期间出错,返回0
return 0;
if( (csd[0]&0xC0) == 0x40 ) //如果为SDHC卡,按照下面方式计算。V2.00的卡
{
csize = csd[9] + ((uint16_t)csd[8] << 8) + 1;
Capacity = (uint32_t)csize << 10; //得到扇区数
}else //V1.xx的卡
{
n = (csd[5] & 15) + ((csd[10] & 128) >> 7) + ((csd[9] & 3) << 1) + 2;
csize = (csd[8] >> 6) + ((uint16_t)csd[7] << 2) + ((uint16_t)(csd[6] & 3) << 10) + 1;
Capacity = (uint32_t)csize << (n - 9); //得到扇区数
}
return Capacity;
}
int MSD0_GetCardInfo(PMSD_CARDINFO SD0_CardInfo)
{
uint8_t r1;
uint8_t CSD_Tab[16], CID_Tab[16];
/* Send CMD9, Read CSD */
r1 = SD_SendCMD(CMD9, 0, 0xFF);
if(r1 != 0x00)
return r1;
if(SD_ReceiveData(CSD_Tab, 16))
return 1;
/* Send CMD10, Read CID */
r1 = SD_SendCMD(CMD10, 0, 0xFF);
if(r1 != 0x00)
return r1;
if(SD_ReceiveData(CID_Tab, 16))
return 2;
/* Byte 0 */
SD0_CardInfo->CSD.CSDStruct = (CSD_Tab[0] & 0xC0) >> 6;
SD0_CardInfo->CSD.SysSpecVersion = (CSD_Tab[0] & 0x3C) >> 2;
SD0_CardInfo->CSD.Reserved1 = CSD_Tab[0] & 0x03;
/* Byte 1 */
SD0_CardInfo->CSD.TAAC = CSD_Tab[1] ;
/* Byte 2 */
SD0_CardInfo->CSD.NSAC = CSD_Tab[2];
/* Byte 3 */
SD0_CardInfo->CSD.MaxBusClkFrec = CSD_Tab[3];
/* Byte 4 */
SD0_CardInfo->CSD.CardComdClasses = CSD_Tab[4] << 4;
/* Byte 5 */
SD0_CardInfo->CSD.CardComdClasses |= (CSD_Tab[5] & 0xF0) >> 4;
SD0_CardInfo->CSD.RdBlockLen = CSD_Tab[5] & 0x0F;
/* Byte 6 */
SD0_CardInfo->CSD.PartBlockRead = (CSD_Tab[6] & 0x80) >> 7;
SD0_CardInfo->CSD.WrBlockMisalign = (CSD_Tab[6] & 0x40) >> 6;
SD0_CardInfo->CSD.RdBlockMisalign = (CSD_Tab[6] & 0x20) >> 5;
SD0_CardInfo->CSD.DSRImpl = (CSD_Tab[6] & 0x10) >> 4;
SD0_CardInfo->CSD.Reserved2 = 0; /* Reserved */
SD0_CardInfo->CSD.DeviceSize = (CSD_Tab[6] & 0x03) << 10;
/* Byte 7 */
SD0_CardInfo->CSD.DeviceSize |= (CSD_Tab[7]) << 2;
/* Byte 8 */
SD0_CardInfo->CSD.DeviceSize |= (CSD_Tab[8] & 0xC0) >> 6;
SD0_CardInfo->CSD.MaxRdCurrentVDDMin = (CSD_Tab[8] & 0x38) >> 3;
SD0_CardInfo->CSD.MaxRdCurrentVDDMax = (CSD_Tab[8] & 0x07);
/* Byte 9 */
SD0_CardInfo->CSD.MaxWrCurrentVDDMin = (CSD_Tab[9] & 0xE0) >> 5;
SD0_CardInfo->CSD.MaxWrCurrentVDDMax = (CSD_Tab[9] & 0x1C) >> 2;
SD0_CardInfo->CSD.DeviceSizeMul = (CSD_Tab[9] & 0x03) << 1;
/* Byte 10 */
SD0_CardInfo->CSD.DeviceSizeMul |= (CSD_Tab[10] & 0x80) >> 7;
SD0_CardInfo->CSD.EraseGrSize = (CSD_Tab[10] & 0x7C) >> 2;
SD0_CardInfo->CSD.EraseGrMul = (CSD_Tab[10] & 0x03) << 3;
/* Byte 11 */
SD0_CardInfo->CSD.EraseGrMul |= (CSD_Tab[11] & 0xE0) >> 5;
SD0_CardInfo->CSD.WrProtectGrSize = (CSD_Tab[11] & 0x1F);
/* Byte 12 */
SD0_CardInfo->CSD.WrProtectGrEnable = (CSD_Tab[12] & 0x80) >> 7;
SD0_CardInfo->CSD.ManDeflECC = (CSD_Tab[12] & 0x60) >> 5;
SD0_CardInfo->CSD.WrSpeedFact = (CSD_Tab[12] & 0x1C) >> 2;
SD0_CardInfo->CSD.MaxWrBlockLen = (CSD_Tab[12] & 0x03) << 2;
/* Byte 13 */
SD0_CardInfo->CSD.MaxWrBlockLen |= (CSD_Tab[13] & 0xc0) >> 6;
SD0_CardInfo->CSD.WriteBlockPaPartial = (CSD_Tab[13] & 0x20) >> 5;
SD0_CardInfo->CSD.Reserved3 = 0;
SD0_CardInfo->CSD.ContentProtectAppli = (CSD_Tab[13] & 0x01);
/* Byte 14 */
SD0_CardInfo->CSD.FileFormatGrouop = (CSD_Tab[14] & 0x80) >> 7;
SD0_CardInfo->CSD.CopyFlag = (CSD_Tab[14] & 0x40) >> 6;
SD0_CardInfo->CSD.PermWrProtect = (CSD_Tab[14] & 0x20) >> 5;
SD0_CardInfo->CSD.TempWrProtect = (CSD_Tab[14] & 0x10) >> 4;
SD0_CardInfo->CSD.FileFormat = (CSD_Tab[14] & 0x0C) >> 2;
SD0_CardInfo->CSD.ECC = (CSD_Tab[14] & 0x03);
/* Byte 15 */
SD0_CardInfo->CSD.CSD_CRC = (CSD_Tab[15] & 0xFE) >> 1;
SD0_CardInfo->CSD.Reserved4 = 1;
if(SD0_CardInfo->CardType == V2HC)
{
/* Byte 7 */
SD0_CardInfo->CSD.DeviceSize = (uint16_t)(CSD_Tab[8]) *256;
/* Byte 8 */
SD0_CardInfo->CSD.DeviceSize += CSD_Tab[9] ;
}
SD0_CardInfo->Capacity = SD0_CardInfo->CSD.DeviceSize * MSD_BLOCKSIZE * 1024;
SD0_CardInfo->BlockSize = MSD_BLOCKSIZE;
/* Byte 0 */
SD0_CardInfo->CID.ManufacturerID = CID_Tab[0];
/* Byte 1 */
SD0_CardInfo->CID.OEM_AppliID = CID_Tab[1] << 8;
/* Byte 2 */
SD0_CardInfo->CID.OEM_AppliID |= CID_Tab[2];
/* Byte 3 */
SD0_CardInfo->CID.ProdName1 = CID_Tab[3] << 24;
/* Byte 4 */
SD0_CardInfo->CID.ProdName1 |= CID_Tab[4] << 16;
/* Byte 5 */
SD0_CardInfo->CID.ProdName1 |= CID_Tab[5] << 8;
/* Byte 6 */
SD0_CardInfo->CID.ProdName1 |= CID_Tab[6];
/* Byte 7 */
SD0_CardInfo->CID.ProdName2 = CID_Tab[7];
/* Byte 8 */
SD0_CardInfo->CID.ProdRev = CID_Tab[8];
/* Byte 9 */
SD0_CardInfo->CID.ProdSN = CID_Tab[9] << 24;
/* Byte 10 */
SD0_CardInfo->CID.ProdSN |= CID_Tab[10] << 16;
/* Byte 11 */
SD0_CardInfo->CID.ProdSN |= CID_Tab[11] << 8;
/* Byte 12 */
SD0_CardInfo->CID.ProdSN |= CID_Tab[12];
/* Byte 13 */
SD0_CardInfo->CID.Reserved1 |= (CID_Tab[13] & 0xF0) >> 4;
/* Byte 14 */
SD0_CardInfo->CID.ManufactDate = (CID_Tab[13] & 0x0F) << 8;
/* Byte 15 */
SD0_CardInfo->CID.ManufactDate |= CID_Tab[14];
/* Byte 16 */
SD0_CardInfo->CID.CID_CRC = (CID_Tab[15] & 0xFE) >> 1;
SD0_CardInfo->CID.Reserved2 = 1;
return 0;
}
//写SD卡
//buf:数据缓存区
//sector:起始扇区
//cnt:扇区数
//返回值:0,ok;其他,失败.
uint8_t SD_WriteDisk(uint8_t *buf, uint32_t sector, uint8_t cnt)
{
uint8_t r1;
if(SD_TYPE != V2HC)
sector *= 512; //转换为字节地址
if(cnt == 1)
{
r1 = SD_SendCMD(CMD24, sector, 0x01); //读命令
if(r1 == 0) //指令发送成功
r1=SD_SendBlock(buf, 0xFE); //写512个字节
}else
{
if(SD_TYPE != MMC)
{
SD_SendCMD(CMD55, 0, 0x01);
SD_SendCMD(CMD23, cnt, 0x01); //发送指令
}
r1 = SD_SendCMD(CMD25, sector, 0x01); //连续读命令
if(r1 == 0)
{
do
{
r1 = SD_SendBlock(buf,0xFC); //接收512个字节
buf += 512;
}while(--cnt && r1==0);
r1 = SD_SendBlock(0,0xFD); //接收512个字节
}
}
SPISD_CS(0); //取消片选
return r1;
}
//读SD卡
//buf:数据缓存区
//sector:扇区
//cnt:扇区数
//返回值:0,ok;其他,失败.
uint8_t SD_ReadDisk(uint8_t*buf,uint32_t sector,uint8_t cnt)
{
uint8_t r1;
if(SD_TYPE != V2HC)
sector <<= 9; //转换为字节地址
if(cnt == 1)
{
r1 = SD_SendCMD(CMD17, sector, 0x01); //读命令
if(r1 == 0)
r1 = SD_ReceiveData(buf, 512); //接收512个字节
}else
{
r1 = SD_SendCMD(CMD18, sector, 0x01); //连续读命令
do
{
r1 = SD_ReceiveData(buf, 512); //接收512个字节
buf += 512;
}while(--cnt && r1==0);
SD_SendCMD(CMD12, 0, 0x01); //发送停止命令
}
SPISD_CS(0); //取消片选
return r1;
}
uint8_t SPI_ReadWrite(uint8_t Txdata)
{
uint8_t Rxdata;
HAL_SPI_TransmitReceive(&hspi1, &Txdata, &Rxdata, 1, 100);
return Rxdata;
}
//SPI1波特率设置
void SPI_SetSpeed(uint8_t speed)
{
hspi1.Init.BaudRatePrescaler = speed;
if (HAL_SPI_Init(&hspi1) != HAL_OK)
{
Error_Handler();
}
}
///////////////////////////END//////////////////////////////////////
然后在文件系统文件夹里修改内容。
user_diskio.c如下
/* USER CODE BEGIN Header */
/**
******************************************************************************
* @file user_diskio.c
* @brief This file includes a diskio driver skeleton to be completed by the user.
******************************************************************************
* @attention
*
* Copyright (c) 2023 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
*/
/* USER CODE END Header */
#ifdef USE_OBSOLETE_USER_CODE_SECTION_0
/*
* Warning: the user section 0 is no more in use (starting from CubeMx version 4.16.0)
* To be suppressed in the future.
* Kept to ensure backward compatibility with previous CubeMx versions when
* migrating projects.
* User code previously added there should be copied in the new user sections before
* the section contents can be deleted.
*/
/* USER CODE BEGIN 0 */
/* USER CODE END 0 */
#endif
/* USER CODE BEGIN DECL */
/* Includes ------------------------------------------------------------------*/
#include <string.h>
#include "ff_gen_drv.h"
/* Private typedef -----------------------------------------------------------*/
#include "drive_spisd.h"
/* Private define ------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Disk status */
static volatile DSTATUS Stat = STA_NOINIT;
/* USER CODE END DECL */
/* Private function prototypes -----------------------------------------------*/
DSTATUS USER_initialize (BYTE pdrv);
DSTATUS USER_status (BYTE pdrv);
DRESULT USER_read (BYTE pdrv, BYTE *buff, DWORD sector, UINT count);
#if _USE_WRITE == 1
DRESULT USER_write (BYTE pdrv, const BYTE *buff, DWORD sector, UINT count);
#endif /* _USE_WRITE == 1 */
#if _USE_IOCTL == 1
DRESULT USER_ioctl (BYTE pdrv, BYTE cmd, void *buff);
#endif /* _USE_IOCTL == 1 */
Diskio_drvTypeDef USER_Driver =
{
USER_initialize,
USER_status,
USER_read,
#if _USE_WRITE
USER_write,
#endif /* _USE_WRITE == 1 */
#if _USE_IOCTL == 1
USER_ioctl,
#endif /* _USE_IOCTL == 1 */
};
/* Private functions ---------------------------------------------------------*/
/**
* @brief Initializes a Drive
* @param pdrv: Physical drive number (0..)
* @retval DSTATUS: Operation status
*/
DSTATUS USER_initialize (
BYTE pdrv /* Physical drive nmuber to identify the drive */
)
{
/* USER CODE BEGIN INIT */
uint8_t res;
res = SD_Init();
if(res) //STM32 SPI的bug,在sd卡操作失败的时候如果不执行下面的语句,可能导致SPI读写异常
{
SPI_SetSpeed(SPI_BAUDRATEPRESCALER_256);
SPI_ReadWrite(0xff); //提供额外的8个时钟
SPI_SetSpeed(SPI_BAUDRATEPRESCALER_4);
}
if(res)
return STA_NOINIT;
else
return RES_OK;
/* USER CODE END INIT */
}
/**
* @brief Gets Disk Status
* @param pdrv: Physical drive number (0..)
* @retval DSTATUS: Operation status
*/
DSTATUS USER_status (
BYTE pdrv /* Physical drive number to identify the drive */
)
{
/* USER CODE BEGIN STATUS */
switch (pdrv)
{
case 0 :
return RES_OK;
case 1 :
return RES_OK;
case 2 :
return RES_OK;
default:
return STA_NOINIT;
}
/* USER CODE END STATUS */
}
/**
* @brief Reads Sector(s)
* @param pdrv: Physical drive number (0..)
* @param *buff: Data buffer to store read data
* @param sector: Sector address (LBA)
* @param count: Number of sectors to read (1..128)
* @retval DRESULT: Operation result
*/
DRESULT USER_read (
BYTE pdrv, /* Physical drive nmuber to identify the drive */
BYTE *buff, /* Data buffer to store read data */
DWORD sector, /* Sector address in LBA */
UINT count /* Number of sectors to read */
)
{
/* USER CODE BEGIN READ */
uint8_t res;
if( !count )
{
return RES_PARERR; /* count不能等于0,否则返回参数错误 */
}
switch (pdrv)
{
case 0:
res = SD_ReadDisk(buff,sector,count);
if(res == 0)
return RES_OK;
else
return RES_ERROR;
default:
return RES_ERROR;
}
/* USER CODE END READ */
}
/**
* @brief Writes Sector(s)
* @param pdrv: Physical drive number (0..)
* @param *buff: Data to be written
* @param sector: Sector address (LBA)
* @param count: Number of sectors to write (1..128)
* @retval DRESULT: Operation result
*/
#if _USE_WRITE == 1
DRESULT USER_write (
BYTE pdrv, /* Physical drive nmuber to identify the drive */
const BYTE *buff, /* Data to be written */
DWORD sector, /* Sector address in LBA */
UINT count /* Number of sectors to write */
)
{
/* USER CODE BEGIN WRITE */
/* USER CODE HERE */
uint8_t res;
if( !count )
return RES_PARERR; /* count不能等于0,否则返回参数错误 */
switch (pdrv)
{
case 0:
res=SD_WriteDisk((uint8_t *)buff,sector,count);
if(res == 0)
return RES_OK;
else
return RES_ERROR;
default:
return RES_ERROR;
}
/* USER CODE END WRITE */
}
#endif /* _USE_WRITE == 1 */
/**
* @brief I/O control operation
* @param pdrv: Physical drive number (0..)
* @param cmd: Control code
* @param *buff: Buffer to send/receive control data
* @retval DRESULT: Operation result
*/
#if _USE_IOCTL == 1
DRESULT USER_ioctl (
BYTE pdrv, /* Physical drive nmuber (0..) */
BYTE cmd, /* Control code */
void *buff /* Buffer to send/receive control data */
)
{
/* USER CODE BEGIN IOCTL */
DRESULT res;
switch(cmd)
{
case CTRL_SYNC:
SPISD_CS(1);
do{
HAL_Delay(20);
}while(SPI_ReadWrite(0xFF)!=0xFF);
res=RES_OK;
SPISD_CS(0);
break;
case GET_SECTOR_SIZE:
*(WORD*)buff = 512;
res = RES_OK;
break;
case GET_BLOCK_SIZE:
*(WORD*)buff = 8;
res = RES_OK;
break;
case GET_SECTOR_COUNT:
*(DWORD*)buff = SD_GetSectorCount();
res = RES_OK;
break;
default:
res = RES_PARERR;
break;
}
return res;
/* USER CODE END IOCTL */
}
#endif /* _USE_IOCTL == 1 */
main.c
/* USER CODE BEGIN Header */
/**
******************************************************************************
* @file : main.c
* @brief : Main program body
******************************************************************************
* @attention
*
* Copyright (c) 2023 STMicroelectronics.
* All rights reserved.
*
* This software is licensed under terms that can be found in the LICENSE file
* in the root directory of this software component.
* If no LICENSE file comes with this software, it is provided AS-IS.
*
******************************************************************************
*/
/* USER CODE END Header */
/* Includes ------------------------------------------------------------------*/
#include "main.h"
#include "fatfs.h"
#include "spi.h"
#include "usart.h"
#include "gpio.h"
/* Private includes ----------------------------------------------------------*/
/* USER CODE BEGIN Includes */
#include "drive_spisd.h"
/* USER CODE END Includes */
/* Private typedef -----------------------------------------------------------*/
/* USER CODE BEGIN PTD */
/* USER CODE END PTD */
/* Private define ------------------------------------------------------------*/
/* USER CODE BEGIN PD */
/* USER CODE END PD */
/* Private macro -------------------------------------------------------------*/
/* USER CODE BEGIN PM */
/* USER CODE END PM */
/* Private variables ---------------------------------------------------------*/
/* USER CODE BEGIN PV */
uint8_t status = 0;
uint8_t writeBuf[] = "demo program forever no bug!!!\r\n";
/* USER CODE END PV */
/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
/* USER CODE BEGIN PFP */
/* USER CODE END PFP */
/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */
/* USER CODE END 0 */
/**
* @brief The application entry point.
* @retval int
*/
int main(void)
{
/* USER CODE BEGIN 1 */
UINT Bw;
FIL file;
uint16_t cb_task = 0;
uint8_t res1 = 0, res2 = 0;
/* USER CODE END 1 */
/* MCU Configuration--------------------------------------------------------*/
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();
/* USER CODE BEGIN Init */
/* USER CODE END Init */
/* Configure the system clock */
SystemClock_Config();
/* USER CODE BEGIN SysInit */
/* USER CODE END SysInit */
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_SPI1_Init();
MX_USART1_UART_Init();
MX_FATFS_Init();
/* USER CODE BEGIN 2 */
FileSystem_Init(); //初始化文件系统
status = 1;
res1 = f_open(&file, "sdRW1.txt", FA_OPEN_ALWAYS | FA_WRITE);
if((res1 & FR_DENIED) == FR_DENIED)
printf("卡存储已满,写入失败! \r\n");
/* USER CODE END 2 */
/* Infinite loop */
/* USER CODE BEGIN WHILE */
while (1)
{
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
if(status == 1)
{
if(res1 == FR_OK)
{
f_lseek(&file, f_size(&file)); //确保写入不会覆盖之前的数据
res2 = f_write(&file, writeBuf, sizeof(writeBuf), &Bw); //写数据到SD卡
if(res2 != FR_OK)
{
printf("文件写入失败! \r\n");
HAL_GPIO_WritePin(User_led_GPIO_Port, User_led_Pin, GPIO_PIN_RESET);
}else
{
HAL_GPIO_WritePin(User_led_GPIO_Port, User_led_Pin, GPIO_PIN_SET);
}
}
else
{
printf("打开文件失败! %d\r\n",res1);
}
if(++cb_task%4096==0)
f_sync(&file);
}else if(status == 2)
{
f_close(&file);
f_mount(NULL, USERPath, 1); //取消挂载
HAL_GPIO_WritePin(User_led_GPIO_Port, User_led_Pin, GPIO_PIN_RESET);
status = 0;
}
HAL_Delay(10);
}
/* USER CODE END 3 */
}
/**
* @brief System Clock Configuration
* @retval None
*/
void SystemClock_Config(void)
{
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
/** Configure the main internal regulator output voltage
*/
__HAL_RCC_PWR_CLK_ENABLE();
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
/** Initializes the RCC Oscillators according to the specified parameters
* in the RCC_OscInitTypeDef structure.
*/
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLM = 4;
RCC_OscInitStruct.PLL.PLLN = 168;
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
RCC_OscInitStruct.PLL.PLLQ = 4;
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
{
Error_Handler();
}
/** Initializes the CPU, AHB and APB buses clocks
*/
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
{
Error_Handler();
}
}
/* USER CODE BEGIN 4 */
void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
{
if(GPIO_Pin == User_Key_Pin)
{
status = 2;
}
}
/* USER CODE END 4 */
/**
* @brief This function is executed in case of error occurrence.
* @retval None
*/
void Error_Handler(void)
{
/* USER CODE BEGIN Error_Handler_Debug */
/* User can add his own implementation to report the HAL error return state */
__disable_irq();
while (1)
{
}
/* USER CODE END Error_Handler_Debug */
}
#ifdef USE_FULL_ASSERT
/**
* @brief Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* @param file: pointer to the source file name
* @param line: assert_param error line source number
* @retval None
*/
void assert_failed(uint8_t *file, uint32_t line)
{
/* USER CODE BEGIN 6 */
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* USER CODE END 6 */
}
#endif /* USE_FULL_ASSERT */
实测是可以的,但是写速度并没有网上说的1M/s那么快,也有可能是我引线的问题。
时代越来越好,开发效率越来越高,希望能帮助到你!!!
还有就是,开源万岁。
评论(0)
您还未登录,请登录后发表或查看评论